HX 05-P/SP2

Current Transducer HX 03..50-P/SP2 IPN = 3 .. 50 A For the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). Electrical data Primary nominal Primary current, current rms measuring range1) IPN (A) IPM (A) 3 5 10 15 20 25 50 ±9 ± 15 ± 30 ± 45 ± 60 ± 75 ± 150 VOUT ROUT RL VC IC Vd Ve VW Primary conductor diameter x turns (mm) 0.6d x 20T 0.8d x 12T 1.1d x 6T 1.4d x 4T 1.6d x 3T 1.6d x 2T 1.2 x 6.3 x 1T Type RoHS since date code • Galvanic isolation between primary HX 03-P/SP2 HX 05-P/SP2 HX 10-P/SP2 HX 15-P/SP2 HX 20-P/SP2 HX 25-P/SP2 HX 50-P/SP2 Output voltage (Analog) @ ± IPN, RL = 2 kΩ, TA = 25°C Output internal resistance Load resistance Supply voltage (± 5 %) Current consumption Rms voltage for AC isolation test, 50 Hz, 1 min Partial discharge extinction voltage rms @ 10 pC Impulse withstand voltage, 1.2/50 µs 46128 46019 45352 46133 planned 46233 46152 VOE ± 0.625 < 50 ≥2 + 12 .. 15 < 15 >3 ≥1 ≥6 V Ω kΩ V mA kV kV kV Accuracy-Dynamic performance data X ε Accuracy @ IPN, TA = 25°C (excluding offset) Linearity error (0 .. ± IPN) Electrical offset voltage @ TA = 25°C Hysteresis offset voltage @ IP = 0; after an excursion of 1 x IPN Temperature coefficient of VOE Temperature coefficient of VOUT (% of reading) Response time to 90% of IPN step Frequency bandwidth (- 3 dB) 2) L VOE VOH TCVOE TCVOUT tr BW Ambient operating temperature Ambient storage temperature Mass Creepage distance Isolation material group Standards • • • • • and secondary circuit Hall effect measuring principle Isolation voltage 3000V Low power consumption Extended measuring range(3x IPN) Isolated plastic case recognized according to UL94-V0. Special feature • Single supply from +12V to +15V Advantages • Low insertion losses • Easy to mount with automatic handling system < ± 1 % of IPN < ± 1 % of IPN + 2.5V ± 50 mV < ± 10 < ± 1.5 ± 0.1 ≤3 50 mV mV/K %/K µs kHz • Small size and space saving • Only one design for wide current ratings range • High immunity to external interference. Applications • Switched Mode Power Supplies (SMPS) • AC variable speed drives • Uninterruptible Power Supplies General data TA TS m dCp Features - 25 .. + 85 °C - 25 .. + 85 °C 8 g ≥ 5.5 mm I EN50178: 1997 (UPS) • Electrical appliances • Battery supplied applications • DC motor drives Application domain • Industrial Notes : 1) 2) With R L=2kΩ Small signal only to avoid excessive heating of the magnetic core Page 1/2 070313/6 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Dimensions HX 03..50-P/SP2 (in mm. 1 mm = 0.0394 inch) HX03..25-P/SP2 02..25-P HX HX 03...25-P HX 50-P HX 50-P/SP2 HX 50-P 19 Max. 19 Max. 20 Max. 3 8.8 3 d 3-P=2.54 5 5 3 +V 2 0 1 -V or 0 1.3 5 15.4 Max. 6 1 -V or 0 6 4 OUT 3 +V 2 0 Primary conductor diameter Bottom view 6 4 OUT 5.4 15.4 Max. Bottom view 1 ..... 0V 2 ..... 0V 3 ..... +12V to +15V 4 ..... Output 5 ..... Primary input Current (+) 6 ..... Primary input Current (-) 0.5 10.85 3 3-P=2.54 3.5 3.5 3.5 0.5 20 Max. Terminal Pin Identification HX 03-P/ SP2 05-P/ SP2 10-P/ SP2 15-P/ SP2 d 0.6 0.8 1.1 1.4 HX 20-P/ SP2 25-P/ SP2 50-P/ SP2 d 1.6 1.6 1.2 x 6.3 1.2 3 10.85 3 8.8 5.4 Secondary pins dimension 0.5 x 0.25 Top view HX HX 05-P 05-P/ SP2 41123 Lot No. Safety Mechanical characteristics • General tolerance ± 0.5 mm This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the following manufacturer's operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/2 070313/6 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com